Fabrication of a Porous Ceramic Material Suitable for Cost-effective Thermal Insulation of Buildings
Автор: Odewole Peter Oluwagbenga, Folorunso Davies Oladayo
Журнал: International Journal of Engineering and Manufacturing @ijem
Статья в выпуске: 5 vol.10, 2020 года.
Бесплатный доступ
The domestication of cost-effective, green, and sustainable building materials is significant towards its massive adoption in the developing countries. The feasibility of developing porous ceramics for cost-effective thermal insulation of buildings was explored in this study using waste materials including granite shifting and sawdust as well as chemical reagents including water glass and sodium hydroxide. Granite shifting and sawdust were dried, processed into powdered form, milled and sieved. Samples of porous ceramics were formulated using varying percentages by weight of granite shifting and sawdust mixed with a constant percentage by weight of water glass and sodium hydroxide in three different cases. The homogenized powder of the formulated composition was uniaxially pressed at 10Mpa. The samples were dried and then sintered in a gas kiln at 8500C for 3 hours. The result revealed water absorption (21.1−56.5%), compressive strength (1.2−7.9Mpa), bulk density (1.44−1.81g/cm3), apparent porosity (38.1−81.3%), and thermal conductivity (0.13−0.54W/m.K). These results indicated that the obtained porous ceramics is a potential material for cost-effective thermal insulation of buildings where a suitable combination of thermal conductivity, porosity, and mechanical strength is required.
Thermal Insulation, Porous Ceramics, Cost-effective Fabrication Technique, Waste Upcycling, Green and Sustainable Building Materials
Короткий адрес: https://sciup.org/15017322
IDR: 15017322 | DOI: 10.5815/ijem.2020.05.05
Список литературы Fabrication of a Porous Ceramic Material Suitable for Cost-effective Thermal Insulation of Buildings
- Choudhary S., Thakur M.S. and Dogne N., Passive cooling techniques, design concept and ventilation techniques, Proceeding to National Conference on Alternative & Innovation Construction Material Techniques TEQIP-II/Civil/AICMT-2, 2014; 5-11.
- Zhang, F. and Cooke, P., Green buildings and energy efficiency, Centre for Advanced Studies, Cardiff University, UK, 2010; 1-28. Available at: https://www.dime-eu.org/files/active/0/Cooke-2010-Fang-Green-building-review.pdf.
- Mardiana A, Riffat S.B., Building energy consumption and carbon dioxide emissions: threat to climate change. J Earth Sci Climat. Change, 2015, S3:001, 1-3, doi:10.4172/2157-7617.S3-001.
- Udodiong I., Here is how to survive the current severe heatwave in Nigeria, 2019. Available at: https://www.pulse.ng/bi/lifestyle/how- to-survive -the-current-severe-heatwave-in-nigeria/2r1c9de
- Sadiq L.,Why Jos has lowest temperature of 6.7 degree Celsius- NCRS, 2020. Available at: https://www.dailytrust.com.ng/why-jos-has-lowest-temperature-of-6-7-degree-celsius-ncrs.html
- Dalibi S.G., Feng J.C., Shuangqin L., Sadiq A., Bello B.S. & Danja I.I., Hindrances to green building developments in Nigeria’s built environment: the project professionals’ perspectives, IOP Conf. Ser.: Earth Environ. Sci., 2017; 63:1-8, doi:10.1088/1755-1315/63/1/012033.
- Odewole P.O., Kashim I.B. and Akinbogun T.L., Towards energy-efficient building design in Nigeria: the possibilities of developing cost-effective wall insulation materials using indigenous ceramic technology, in 1st Visual Communication Design Conference, Federal University of Technology, Akure, Nigeria, 2019; 267-283.
- United Nations Industrial Development Organization (UNIDO), Thermal insulation properties and application in houses: technical manual, Vienna International Centre, Vienna, Austria, 2017. Available at: https://www.unido.org/sites/default/files/2017-09/House_Insulation_v_5.8_EN_0.pdf
- Taurino R., Lancellotti I., Barbieri L., and Leonelli C., Glass-ceramic foam from borosilicate glass, International Journal of Applied Glass Science, 2014; 1–10, DOI:10.1111/ijag.12069.
- Chinnam R. K., Bernardo E., Will J. and Boccaccini A. R., Processing of porous glass ceramics from highly crystallisable industrial wastes, Advances in Applied Ceramics, 2015; 114: sup1, S11-S16, doi: 10.1179/1743676115Y.0000000053.
- Chinnam, R.K., Functional glasses and glass-ceramics derived from industrial waste, doctoral dissertation, Department of Material Science and Engineering, Friedrich-Alexander-Universität Erlangen-Nürnberg, Germany, 2014. Available at: opus4.kobv.de›files› PhD_Thesis_Chinnam_WW7.
- Zhu M., Ji R., Li Z., Wang H., Liu L. and Zhang Z., Preparation of glass-ceramic foams for thermal insulation applications from coal fly ash and waste glass, Construction and Building Materials, 2016; 112: 398-405, doi: http://dx.doi.org/10.1016/j.conbuildmat.2016.02.183.
- Ivanov K.S., Preparation and properties of foam glass-ceramic from diatomite, Journal of Wuhan University of Technology-Mater. Sci. Ed., 2018; 273-277. DOI: https: //doi. org/10.1007/s11595-018-1817-8
- Kazmina O., Volkova A., Veresсhagin V. and Rymanova I., Single-stage technology for granulated foam glass production based on the composition of tripoli and technological microsilica, IOP Conf. Ser.: Earth Environ. Sci., 2016; 43: 1-4, doi:10.1088/1755-1315/43/1/012067.
- Saakyan E., Arzumanyan A. and Galstyan G., Chemical technology of cellular glass production, E3S Web of Conferences, 2019; 97 (02012): 1-6, doi: https://doi.org/10.1051/e3sconf/20199702012.
- Lameed G.A. and Ayodele A.E. (2010) Effect of quarrying activity on biodiversity: case study of Ogbere site, Ogun State Nigeria, African Journal of Environmental Science and Technology, 4 (11): 740-750. ISSN 1991-637X.
- Ayodele O.J., Shittu O.S., Balogun T., Heavy metal pollution assessment of granite quarrying operations at Ikole-Ekiti, Nigeria, International Journal of Environmental Monitoring and Analysis, 2014; 2 (6): 333-339, doi: 10.11648/j.ijema.20140206.16.
- Eshiwani F., Effects of quarrying activities on the environment in Nairobi county: a case study of Embakasi District, Master Thesis, Department of Geography and Environmental Studies, University of Nairobi, Kenya, 2014. Available at: https://pdfs.semanticscholar.org/fb69/4269047997e656bd90ebd1d92f8d846fadf6.pdf
- de Lima-Filho V.X., Blazdell P.F., Nogueira R.E.F.Q. and Braga R., Studies on sintering of molded granite bodies, Congresso Brasileiro De Engenharia Ciência Dos Materiais, 2000; 14: 10401- 10411.
- Dhanapandiana S. and Shanthib M., Utilization of marble and granite wastes in brick products, Journal of Industrial Pollution Control, 2009; 25 (2): 145-150.
- Bayraka G. and Yilmazb S., Granite based glass-ceramic materials, Acta Physica Polonica A, 2014; 125 (2): 623-625, doi 10.12693/APhysPolA.125.623.
- Bobkova N.M., Barantseva S.E., and Trusova1 E.E., Production of foam glass with granite siftings from the Mikashevichi deposit, Glass and Ceramics, 2007; 64 (1–2): 47-50.
- da Silva L.L., Ribeiro L.C.N., Santacruz G., Arcaro S., Alves A.K. & Bergmann C.P., Glass foams produced from glass and Yerba Mate (Ilex Paraguarinensis) waste, FME Transactions, 2018; 46 (1) 70-79.
- Mothé C.G. and Ambrósio M.C.R., Processes occurring during the sintering of porous ceramic materials by TG/DSC, Journal of Thermal Analysis and Calorimetry, 2007; 87 (3): 819–822.
- Chemani H. and Chemani B., Effect of adding sawdust on mechanical-physical properties of ceramic bricks to obtain lightweight building material, International Scholarly and Scientific Research & Innovation, 2012; 6 (11): 2521- 2525.
- Butt W.A., Gupta K. & Jha J.N., Strength behavior of clayey soil stabilized with saw dust ash, International Journal of Geo-Engineering, 2016; 7 (18): 2-9, doi 10.1186/s40703-016-0032-9.
- Elinwa A.U., Effect of addition of sawdust ash to clay bricks, Civil Engineering and Environmental Systems, 2006; 23 (4): 263–270, doi 10.1080/10286600600763149.
- Chemani H. and Chemani B., Valorization of wood sawdust in making porous clay brick, Academic Journals, 2013; 8 (15): 609-614, doi 10.5897/SRE12.608.
- Phonphuak N. et al, The use of sawdust waste on physical properties and thermal conductivity of fired clay brick production, International Journal of GEOMATE, 2020, 18 (69): 24-29, https://doi.org/10.21660/2020.69.5706
- Cultrone G., Aurrekoetxea I., Casado C. & Arizzi A. Sawdust recycling in the production of lightweight bricks: How the amount of additive and the firing temperature influence the physical properties of the bricks, Construction and Building Materials, 2020; 235, (117436): 1-13, DOI: https://doi.org/10.1016/j.conbuildmat.2019.117436
- Aramide F.O., Production and characterization of porous insulating fired bricks from Ifon clay with varied sawdust admixture, Journal of Minerals and Materials Characterization and Engineering, 2012; 11, 970-975, doi 10.4236/jmmce.2012.1110097.
- Adebisi I.I, Ayinla A.K. and Okeyinka Y.R. (2018) Energy Efficient Buildings in Tropical Climate through Passive Techniques- An Overview, Journal of Environment and Earth Science, 8 (4): 45-50.
- . Rashidi A., Esfahani J.A. and Karimi N., Renewable and Sustainable Energy Reviews, 91 (2018) 229.
- Rincon A., Marangoni M., Cetin S. and Bernardo E., Recycling of inorganic waste in monolithic and cellular glass-based materials for structural and functional applications, J. Chem. Technol. Biotechnol., vol. 91, pp. 1946-1961, 2016, doi: https://doi.org/10.1002/jctb.4982.
- Khamidulina D.D., Nekrasova S.A., and Voronin K.M., ''Foam glass production from waste glass by compression,'' IOP Conf. Ser. Mater. Sci. Eng., vol. 262, no. 1, 2017, doi: 10.1088/1757-899X/262/1/012008.
- Dragoescu M.F., Axinte S.M., Paunescu L. and Fiti A. (2018) Foam glass with low apparent density and thermal conductivity produced by microwave heating, European Journal of Engineering and Technology, 6 (2):1-9
- Yuan H., Wu H., and Guan J., ''Synthesis of foam glass-ceramic from CRT panel glass using one-step powder sintering,'' IOP Conf. Ser. Earth Environ. Sci., vol. 186, no. 2, 2018, doi: 10.1088/1755-1315/186/2/012020.
- Cheng C., Feng K., Zhou Y., and Zhou H., ''Effect of sintering temperature on the microstructure and properties of foamed glass-ceramics prepared from high-titanium blast furnace slag and waste glass,'' Int. J. Miner. Metall. Mater., vol. 24, no. 8, pp. 931–936, 2017, doi: 10.1007/s12613-017-1480-8.
- ASTM C20-00, “Standard test methods for apparent porosity, water absorption, apparent specific gravity, and bulk density of burned refractory brick and shapes by boiling water”, ASTM International, West Conshohocken, PA (2010).
- ASTM C240-97, “Standard test methods of testing cellular glass insulation block”, ASTM International, West Conshohocken, PA (1998).
- Obidiegwu E.O., Esezobor D.E., Agunsoye J.O. and Lawal G.I., Enhancement of insulating refractory properties of selected Nigeria fire-clays using coconut shell, Journal of Minerals and Materials Characterization and Engineering, 2015; 3: 458-468, http://dx.doi.org/10.4236/jmmce.2015.36048.
- Aramide, F.O. (2012), “Production and characterization of porous insulating fired bricks from Ifon clay with varied sawdust admixture”, Journal of Minerals and Materials Characterization and Engineering, Vol. 11, pp. 970-975.
- Folorunso D.O., Characterization and value enhancement of some Nigerian refractory materials for thermal insulation, IOSR Journ. of Mech. and Civil Eng. (IOSR-JMCE), 2018, 15 (3-3): 79-86, doi: 10.9790/1684-1503037986.
- da Silva R.C., Kubaski E.T., and Tebcherami S.M., Glass foams produced by glass waste, sodium hydroxide, and borax with several pore structures using factorial designs, Int. J. Appl. Ceram. Technol., 2019; 1-9, doi 10.1111/ijac.13210.
- Zhu, M., Ji, R., Li, Z., Wang, H., Liu, L. and Zhang, Z. (2016), “Preparation of glass-ceramic foams for thermal insulation applications from coal fly ash and waste glass”, Construction and Building Materials, Vol. 112, pp. 398-405.
Статья научная
