Разработка методики определения прочности фруктово-ягодных батончиков с использованием прибора «Структурометр СТ-2»
Журнал: Вестник Воронежского государственного университета инженерных технологий @vestnik-vsuet
Рубрика: Пищевые системы
Статья в выпуске: 3 (109) т.88, 2026 года.
Бесплатный доступ
В настоящее время в пищевой промышленности отсутствует стандартизированная методика оценки прочности фруктово-ягодных батончиков на приборе «Структурометр СТ-2», что затрудняет объективный контроль качества как в производственных условиях, так и при разработке новых рецептур. В данной работе предложено комплексное решение этой проблемы. Проведен сравнительный анализ трех типов инденторов («Нож No1», «Конус 60», «Цилиндр Ø1») с оценкой воспроизводимости результатов (коэффициент вариации – СV). Установлено, что индентор «НожNo1» демонстрирует наилучшее сочетание воспроизводимости (CV = 10,4 %) и способности адекватно оценивать прочностные характеристики батончика при изгибе. Рассчитано отношение пластической деформации к упругой (plastic/ elastic), что подтверждает вязкопластичное поведение продукта (пластическая деформация в 2,7 раза превышает упругую). Коэффициент эластичности (Eel=7,5 %) является второстепенным параметром и указывает на низкую способность батончика к восстановлению формы. Выполнена математическая интерпретация кривых нагружения с выделением стадий деформации: упругой (линейная зависимость F = 65,0h+18,9, R2 = 0,997), пластической (полином F = - 0,631h2+109,0h-286,8, R2 = 0,996) и разгрузки. Полученные регрессионные модели количественно описывают структурно-механические свойства фруктово-ягодного батончика, в частности, жесткость при изгибе (коэффициент жесткости 65 г/мм). Разработанная методика апробирована на батончике с фруктово-ореховым составом и представляет практическую ценность для стандартизации контроля структурно-механических показателей данного вида продукции.
Короткий адрес: https://sciup.org/140317027
IDS: 140317027 | УДК: 664.8:634 | DOI: 10.20914/2310-1202-2026-3-145-153
Development of a method for determining the strength of fruit and berry bars using the «Strukturometer ST-2» device
Currently, the food industry lacks a standardized method for assessing the strength of fruit and berry bars using the «Strukturometer ST-2» device, which significantly limits the possibilities of objective quality control in both industrial settings and the development of new recipes. This paper presents a comprehensive solution to this problem. A comparative analysis of three types of indenters («Knife No. 1», «Cone 60», «Cylinder Ø1») was carried out with an assessment of the reproducibility of the results (coefficient of variation – CV). It was found that the «Knife No. 1» indenter demonstrates the best combination of reproducibility (CV = 10.4 %) and the ability to adequately assess the strength characteristics of the bar under bending. The ratio of plastic deformation to elastic deformation (Δhplastic/Δhelastic) was calculated, which confirms the visco-plastic behavior of the product (plastic deformation is 2.7 times higher than elastic deformation). The elasticity index (Eel = 7.5 %) is a secondary parameter and indicates the low ability of the bar to recover its shape after loading. Mathematical interpretation of the loading curves was performed, identifying the stages of deformation: elastic (linear dependence F = 65.0h + 18.9, R2 = 0.997), plastic (polynomial F = -0.631h2 + 109.0h - 286.8, R2 = 0.996) and unloading. The obtained regression models quantitatively describe the structural and mechanical properties of the fruit and berry bar, in particular, the bending stiffness (stiffness coefficient 65 g/mm). The developed method was tested on a bar with a fruit-nut composition and is of practical value for standardizing the control of structural and mechanical parameters of this type of product.