Page 11. Mechanical technology in general: processes, tools, machines, equipment UDC: 621.7

Study of the quality of weld seam obtained by welding with barium-strontium carbonatite flux

Kozyrev N.A., Kryukov R.E., Usoltsev A.A., Prokhorenko O.D., Aimatov V.G.

On shear nucleation sites at phase transformations in steel

Pustovoit V.N., Dolgachev Yu.V., Dombrovskii Yu.M., Kornilov Yu.A.

Vibration piercing of pipe billet on the piercing press of pipe-rolling mill

Rakhmanov S.R.

Statistical analysis and calculation of metal forming during rolling of h-beam profiles on the universal rail-beam mill

Shilov V.A., Nepryakhin S.O., Shvarts D.L.

Elastoplastic bend of round steel beam. Report 1. Springback coefficient

Shinkin V.N.

Thermodynamic assessment of WO3 reduction by carbon and silicon

Bendre Yu.V., Goryushkin V.F., Kryukov R.E., Kozyrev N.A., Bashchenko L.P.

Influence of friction on shaping of a flat blank

Tishchuk L.I., Solomonov K.N.

Load and strain status of CCM backups and stripe deformation at production of steel sheets for welded pipes. Report 1

Lekhov O.S., Mikhalev A.V., Shevelev M.M.

Investigation and development of welding fluxes with the use of ladle electric-furnace slag and barium-strontium modifier for rolls surfacing

Kozyrev N.A., Kryukov R.E., Umanskii A.A., Mikhno A.R., Dumova L.V.

Investigation of viscosity of liquid welding slags and melts of electrode coatings

Mikhailitsyn S.V., Sheksheev M.A., Platov S.I., Emelyushin A.N., Naumov S.V.

Mathematical models of mechanisms for rolled products accelerated cooling

Sarychev V.D., Khaimzon B.B., Nevskii S.A., Ilyashchenko A.V., Grishunin V.A.

Influence of bending efforts of working rolls on widening of the thin steel strip during hot rolling

Koinov T., Belskii S.M., Mukhin Yu.A., Chuprov V.B.

The concept of optimal bar roll design. Report 2. Calibers space

Mikhailenko A.M., Shvarts D.L.

Simulation of the process of continuous forming of straight-seam welded pipes on the basis of “Tesa 10-50 Trainer”

Samusev S.V., Aleshchenko A.S., Fadeev V.A.

Influence of wheel billet stamping schemes on power modes of forming press operation and on wear of the deformation tool

Snitko S.A., Yakovchenko A.V., Sotnikov A.L.

Research of the behavior of macrostructure defects of the pre-deformed continuous cast billets during rolling

Smirnov E.N., Sklyar V.A., Smirnov O.E., Belevitin V.A., Pivovarov R.E.

Application of water-air cooling technologies for heat treatment of bearing rings

Yaroshenko Yu.G., Lipunov Yu.I., Smakhanov A.B., Stolyarova M.V.

Load and strain status of CCM backups and stripe deformation at production of steel sheets for welded pipes. Report 2

Lekhov O.S., Mikhalev A.V., Shevelev M.M.

Fracture resistance of “transition” area in three-layer steel/vanadium alloy/steel composite after thermomechanical treatment

Nechaikina T.A., Nikulin S.A., Rogachev S.O., Turilina V.Yu., Baranova A.P.

Model studies of hydrodynamic changes of steel flows in mold of slab CCM during submerged nozzles replacement

Eronko S.P., Zolotukhin V.I., Tkachev M.Yu., Provotorov D.A., Oshovskaya E.V.

Assessment of the efficiency of using blind feeders of various geometry based on mathematical simulation results

Fedosov A.V., Chumachenko G.V., Khodarev M.A., Golomeev V.V.

Evaluation of quality of rolled steel for cold volume forging

Filippov A.A., Pachurin G.V., Kuzmin N.A., Matveev Yu.I., Deev V.B.

Investigation of structure and several properties of carbon steel of grade 50 deformed by drawing

Chukin M.V., Polyakova M.A., Pivovarova K.G., Efimova Yu.yu., Gulin A.E.

Heat-insulating mortar based on composite binder

Sumskoi D.A.

Model of layered flow of viscous-plastic Bingham fluid in the extruder channel

Gukasyan A.V.

Software of the extrusion process abnormally viscous fluids methods of experiment planning

Vasilenko V.N., Frolova L.N., Derkanosova A.A., Mikhailova N.A., Shhepkina A.A., Davydov A.M.

Private banking: domestic and foreign experience (on the example of Russia and Switzerland)

Medvedeva M.A., Smirnova V.V.

Strategic approaches to the development of liberty manufacture of Russia

Taranenko L.O.

State-private partnership as factor of development of mining engineering of the Russian Federation

Fetisova A.A., Kazachenko S.I.

Establishment of regularity of changes in chemical characteristics of intermetallides of aluminum systems - lantanides of compounds Al11lN3, -Al11lN3 and Al3lN

Chamanova M., Akhmedov Sh.A., Nazhmudinov Sh.Z., Badalov A.

Assessment of the manufactured risks of manufacture of varnished tape from aluminum alloys

Shkaruppa S.P.

The calculation of technological effort for impact perforation and parts and products marking

O.S. Polishchuk

Исследование износостойкости композитных покрытий, полученных при карбовибродуговом упрочнении

Коломейченко Александр Викторович, Кравченко Игорь Николаевич, Титов Николай Владимирович, Зубенко Елена Васильевна, Багринцев Олег Олегович

Low-cycle fatigue of welded structures made from domestic and imported materials

Vasechkin M.A., Egorov S.V., Kolomensky A.B., Chertov E.D.

Development of an automated control system for the reactor of motor oil production

Kuzichkin A.A., Saveleva Yu. O., Kuzovenkov L.S.

Heat storage materials based on nanomodified paraffin, controlled by a magnetic field

Shchegolkov Alexander.V., Shchegolkov A.V., Yagubov V.S., Zorin A.S., Kobelev A.V.

Selective modification of dual phase steel DP 1000 by laser action using diffractive optical element

Murzin Serguei Petrovich, Blokhin Maksim Vitalievich

Influence of basic parameters on the process of pressing of safflower seeds in an ultrasonic field

Antipov S.T., Shakhov S.V., Martekha A.N., Yurova I.S., Berestovoy A.A., Litvinova M.I.

Study of abutment pressure zone formation in the system of "paired drifts"

Titov N.V., Ivanov S.I.

The physical and mechanical properties, a model of formation and structure of the protective films on carbon-based

Nikolaev D.P.

Mechanical technology in general: processes, tools, machines, equipment - 621.7

Scientific articles