Scientific articles \ Applied sciences. Medicine. Technology \ Engineering. Technology in general \ Mechanical engineering in general. Nuclear technology. Electrical engineering. Machinery

Working or machining with chip formation. Abrasive working. Hammers and presses - 621.9

Scientific articles

In section "Working or machining with chip formation. Abrasive working. Hammers and presses"
The evaluation of temperature distribution in a local zone under conditions of free orthogonal cutting
Fominoff E.V., Chernov I.S., Shuchev C.G.
Calculation of probability of selection intra-mill device
Pusnaya O.P., Putivzeva N.P., Zaitseva T.V.
A portage, passport system and tests of metal-cutting machine tools
Fedorov V.E., Glushkov G.E.
Analysis and calculation of wear rate of gear teeth and gears
Borisov E.A., Teplov A.V., Kudermetova J.C., Lobyntseva O.A.
Rationality of application of the method of restoration of oil pump housings by cold gas-dynamic spraying
Borisov E.A., Teplov A.V., Kudermetova J.C., Lobyntseva O.A.
Conveyors of industrial production
Fedorov V.E., Glushkov G.E.
The method of constructing the same type of three-dimensional models through the creation of families of parts in NX
Nabiullin I.I.
Principles of development of design documentation in the mode of the automated design process of clothing
Juraeva M.I., Kamolova S.U.
Анализ работы обслуживания магазина "Удача" с использованием теории одноканальной системы массового обслуживания с ограниченной длиной очереди
Дулина Я.Р.
Сравнение методов формирования функции распределения по времени в среде моделирования GPSS для многоканальной СМО с бесконечным буфером
Галимов Р.З., Золотов А.А., Третьякова А.А.
Designing the information structure of the navigation menu for the pipe plant site by the open sorting method
Rybanov A.A., Gnatyuk E.S.
Analysis of the technological design of the component
Bagautdinov I.Z.
Thermal high-efficiency coefficient of screens
Kuvshinov N.E.
Classification of dust leaders
Aryshtaev A.A.
Pneumatic gripping devices in the technological system "equipment - industrial robot - gripper - detail"
Nikinin A.V., Sentyakov B.A.
The peculiarity of imitation simulation of the forming formation process with deep cutting
Popova A.A.
Robotics complex for technological process of installing and fixing the upper-end piece on to the covering tube
Bikkinin D.M., Klevakin M.A.
Axial combined instruments (design and operation recommendations)
Shapagatov S.R., Ivanova T.I., Tsyplov E.A., Novikov V.A.
Increase the efficiency of machining by choosing rational conditions
Shapagatov S.R., Ivanova T.I., Tsyplov E.A., Novikov V.A.
Organizational questions of the metrological support of the enterprise at the present stage
Muchkaeva G.M., Balinova T.A., Baryshev V.L.-G., Biryukov A.S.
Analysis of development of the enterprise management system through introduction of innovative proposals
Sapunova T.A., Kim K.T.
Modernization of packing device milk processing plant
Lemeshko M.A., Lapin K.I.
Comparison of heat transfer coefficient in heat exchange equipment
Chushnikova K.A., Mukhanov S.S.
Analysis of dangerous and harmful factors and development of measures to reduce the noise level in the workplace of the meat processor of meat products meat processing shop
Musina S.A., Khasanova L.F., Shchelchkova A.I.
Методы управления изготовлением изделий на станках с ЧПУ при использовании датчиков контактного типа
Федоров В.Е., Глушков Г.Е.
Development of a device to verify the suitability of filter respirators
Ishmukhametova R.I., Timofeev A.L.
Technology the technical control of plug gages to monitor the internal metric thread
Podryadova E.V.
The calculation of the efficiency of the technological process of manufacturing parts of type "blade"
Burzenia E.Y.
Kinematics of the drive as the function of the angle of a rotation of the platform of a manipulator
Shamutdinov A.H., Leonov D.I.
Abrasive flow machining and forces applied to the machined surfaces
Litvinenko D.S.
Unit for machining a waveguide canals with free abrasive particles
Litvinenko D.S., Zverintseva L.V.
Application of the device of interval analysis for adaptive management of formal in composition
Rakhmonova H.Z., Ismoilov E.U.
Teaching technology of metal processing on milling machines and its innovative methods
Mahmudova M.A.
The process of disassembly of riots and supply of raw cotton into pneumatic pipeline of cotton factories
Usmanov J.A., Nurmatova S.S.
Features of identification of industrial paint and varnish materials by thermal analysis
Islamova S.T.
Пилталаш жараёнида масулот нотекислигиникамайтириш услуби
Абдугаффаров А.А., Очилов Т.А., Атанафасов М.Р.
Пилталаш жараёнида ИП сифатини яхшилаш
Абдугаффаров А.А., Очилов Т.А., Атанафасов М.Р.
Пилталаш жараёнида масулот нотекислигини камайтириш асосида сифатли ип ишлаб чиариш
Очилов Т.А., Холияров М.Ш., Джуманизов М.Б., Атанафасов М.Р.
The main tools used in the finishing-strengthening of details using the method of plastic deformation of the inner cylindrical surface layer
Maxmudov A.A., Mukhtorov A.M., Turgunbekov A.M.
Titan qotishmali detallarning yuqori sifatli yuzasini tayyorlash texnonologiyasini ishlab chiqish
Botirov A.A.
QR code for installing the SciUp app Point your camera and download the free app SciUp