Page 12. Working or machining with chip formation. Abrasive working. Hammers and presses UDC: 621.9

The influence of friction geomodifiers on the tribosystems balance

Zlobin V.G., Volkov Yu.V.

On the choice of rational parameters of a hammer mill with a monolithic hammer

Baldanov M.B., Sergeev Yu.A., Konovalov V.I., Konovalova A.A.

Introduction of modern technologies for thread holes cutting in hard-to- cut materials

Kurbanov A.Z., Vagabov N.M., Magomedova M.A., Omardibirov O.M.

Influence of stiffness of the mechanical part of the drive and cutting parameters on the shaping elastic deformation control

Zakovorotny V. L., Gvindjiliya V. E., Zakalyuzhny A. A.

Preparation of production of block-modular milling cutters using 3D prototyping

Popok Nikolay, Partsianka Siarhei

Investigation of the operating modes of a centrifugal mixer of bulk components

Matyushev V.V., Bochkarev A.N., Semenov A.V., Chaplygina I.A.

Results with anti-adhesion gel used for simulated contusion spinal cord injury in rats

Kubrak Nadezhda V., Varsegova Tatiana N., Krasnov Vitaliy V., Ryabykh Sergey O.

CONSTRUCTION OF AN OPTICAL COAGULOMETER SYSTEM AND WAYS TO REDUCE INTERFERENCE

P. O. Lugovaya, T. V. Mirina

Tribotechnical properties of experimental hard alloys with modified cobalt binder

Fominov E.V., Shuchev C.G., Aliev M.M.

Analysis of automated surface roughness parameter support systems based on dynamic monitoring

Gimadeev M. R., Li A. A.

Study of the effect of cutting modes on output parameters under high-speed steel turn-milling

Matlygin D. A., Savilov A. V., Pyatykh A. S., Timofeev S. A.

Comprehensive assessment of the manufacturability of products

Bochkaryov P.Yu., Korolev R.D., Bokova L.G.

Influence of the sphero-cylindrical tool orientation angles on roughness under processing complex-profile surfaces

Gimadeev M.R., Nikitenko A.V., Berkun V.O.

Improving the principles of identifying critical requirements for the assembly of high-precision products

Nazaryev A.V., Bochkarev P.Yu.

Rheological behavior of mixtures used in 3d-printing: ex-perimental evaluation of the effectiveness of criteria requirements for filler

Slavcheva G.S., Solonina V.A., Razov I.O., Filipenko P.V., Orlov V.S.

Энергетические процессы при аэродинамическом звуковом упрочнении концевого фрезерного инструмента из быстрорежущей стали Р6М5

И. А. Горавский, А. Н. Жигалов

Рациональное применение модульных конструкций режущих инструментов на основе уравнивания стойкости различных их типов в инструментальных магазинах станков с ЧПУ

Н. Н. Попок, Р. С. Хмельницкий, В. С. Анисимов, Д. А. Башлачёв

Hand injuries sustained while contacting operating electric meat grinders (literature review illustrated with authors’ clinical cases)

Suprunov I. K., Skryabin E. G.

Effect of Periodic Fluctuations of Cutting Mode Parameters on the Temperature of the Front Face of a Turning Tool

Fominov E.V., Gvindjiliya V.E., Marchenko A.A., Shuchev C.G.

Evaluation of import dependence in the market of machine tool industry products of the Russian Federation

Trifonov P.V., Macheret A.D., Polukarova S.N.

Assessment of protective coatings adhesion on steel linear structures under laser nanostructuring

Shegolkov N.I., Komarova L.Yu, Lisienkova L.N., Budnikova O.A., Varfalovskaya V.V., Tsybin A.I.

Vibration Control of Tool Flank Wear in Turning

Gvindjiliya V.Е.

Kinematics of the movement of separated grain on a flat sieve performing transverse oscillations

Sabiev U.K., Shumel I.I.

Experimental and Curvature-Based Analysis for Accuracy Optimization in 3-Axis CNC Milling of Concave Parabolic Freeform Surfaces

Ngoc T.B., Nguyen T.V.

Optimizing machining parameters for milling pockets in waffle-grid shell structures

Zaytsev Aleksey Mikhaylovich, Shachnev Sergey Yuryevich, Grubyi Sergey Vitalyevich

A study of ultrasonic milling of high-strength ceramics used in manufacturing of components for aerospace hardware

Koziner Yury Dmitrievich, Kravtsov Dmitry Aleksandrovich, Pozhidaev Aleksey Alekseevich

Frequency-response analysis of ultrasound diamond milling of high-strength ceramics

Koziner Yu.D., Kravtsov D.A.

Negative compliance of energy-saving adaptive journal hydrostatic bearing with a restriction of the output lubricant stream

Kodnyanko Vladimir A.

Stability of energy-saving adaptive journal hydrostatic bearing with a restriction of the output lubricant stream

Kodnyanko Vladimir A.

Static characteristics of active hydrostatic two-row radial bearing with restriction of output lubricant flow

Kodnyanko Vladimir A.

On creation of multi-wave screens

Isakov Vladimir P., Burenin Anatoli N., Khudina Marija V.

Modeling of heat exchange processes under electrocontact cutting of metals

Veretnova Tatyana A., Shestakov Ivan Ya., Kovaleva Angelina A., Tinkova Svetlana M., Kosovich Aleksander A.

Numeric-analytical method for determining the communication equations of Laplace’s transformants of the universal radial unit of externally-pressurized gas bearings

Kodnyanko Vladimir A.

Characteristics of radial gas-static bearing of step type

Kodnyanko Vladimir A.

The immunity of non-coherent and coherent reception of a signal DQPSK in the conditions of influence of PSK, a harmonic interference or Gaussian noise

Lozhkin Konstantin Yu., Stitsenko Alexander I.

Compliance of gas-dynamic bearing with elastic compensator of movement

Kodnyanko Vladimir A., Kurzakov Andrei S.

Моделирование технологических процессов знакопеременного изгиба

Бояршинов М.Г.

Сравнительный анализ одномерной и двумерной моделей электронно-лучевой наплавки покрытий с модифицирующими частицами

Крюкова О.Н., Князева А.Г.

Chemical-mechanical polishing. Part 1. Main characteristic: review

Goldstein Robert Veniaminovich, Osipenko Nikolay Michailovich

Chemical-mechanical polishing. Part II. Model of local interactions

Goldstein Robert Veniaminovich, Osipenko Nikolay Michailovich

Working or machining with chip formation. Abrasive working. Hammers and presses - 621.9

Scientific articles